
Đánh giá mối liên hệ của hiệu ứng vành đai và độ sâu đặt chốt trong ống tủy lên độ kháng gãy và khảo sát kiểu gãy của răng được gia cố bằng chốt sợi dưới tác dụng của lực nén. Phương pháp: Nghiên cứu invitro được thực hiện trên 60 răng cối nhỏ hàm dưới đã điều trị nội nha và cắt bỏ thân răng phía trên đường tiếp nối men-cement 2 mm. Các răng được chia ngẫu nhiên thành 4 nhóm (n=15) với sự kết hợp giữa chiều cao của vành đai là 0 mm, 2 mm và độ sâu đặt chốt là 7 mm, 9 mm. Thân răng được tái tạo bằng composite đắp lớp và được phục hồi bằng mão kim loại. Đặt 1 lực hợp với trục răng 1 góc 45 độ, ghi lại giá trị của lực đo khi máy đo báo bắt đầ xuất hiện sự nứt gãy đầu tiên đồng thời khảo sát kiểu nứt gãy của các mẫu nghiên cứu. Xử lý số liệu và so sánh độ kháng gãy các nhóm bằng phần mềm SPSS 20.0. Kết quả: Lực kháng gãy trung bình của 4 nhóm lần lượt là 459,97 ± 115,92N, 495,96 ± 97,92N, 298,54 ± 82,46N, 394,40 ± 88,67N. Khi so sánh các nhóm có hoặc không có hiệu ứng vành đai hoặc giữa các nhóm có độ sâu đặt chốt khác nhau, sự khác biệt về lực gây nứt gãy đều có ý nghĩa thống kê (p < 0,05). Số răng bị nứt gãy có thể sửa chữa cao nhất ở nhóm có hiệu ứng vành đai và độ sâu đặt chốt 9 mm, thấp nhất ở nhóm không có hiệu ứng vành đai và độ sâu đặt chốt 7 mm. Kết luận: Hiệu ứng vành đai và độ sâu đặt chốt đều ảnh hưởng tích cực đến độ kháng gãy. Tăng chiều cao vành đai và độ sâu đặt chốt giúp tạo ra các kiểu nứt gãy thuận lợi hơn cho khả năng sửa chữa do nứt gãy.
The glass fiber post system with a similar elastic modulus to dentin is widely indicated to reinforce teeth after the endodontic treatment. Many studies emphasized the importance of ferrule effect and post length in strengthening endodontically treated teeth. However, the simultaneous influence of 2 factors on increasing fracture resistance is still controversial. Objectives: To evaluate the influence of ferrule effect and depth of glass fiber post insertion on the fracture resistance and the failure mode of endodontically treated teeth. Material and methods: In this in vitro study, sixty sound mandibular first premolars were performed endodontic treatment, and the crown was removed at 2 mm above the cementoenamel junction. Combinations of post lengths of 7 mm, 9 mm, and ferrule lengths of 0 mm and 2 mm formed four different groups consisting of 15 teeth each. The coronal sections were restored by composite build-up technique and received a full metal crown. The fracture load and failure pattern of each group were evaluated by applying a compressive load to the buccal surface of the tooth until the failure occurred. The data were analyzed with SPSS version 20.0. Results: The mean fracture load of 4 groups is 459.97 ± 115.92N, 495.96 ± 97.92N, 298.54 ± 82.46 N, 394.40 ± 88.67N, respectively. The difference in resistance to fracture between groups with ferrule and without ferrule or between groups with different post length insertions were statistically significant (p < 0.05). The number of favorable fractured teeth was highest in the group with ferrule effect and post length at 9 mm, whereas the lowest in the group without ferrule effect and with shorter post length. Conclusion: Both ferrule effect and post length play an important role in improving the fracture resistance to compressive load in endodontically treated teeth. The ferrule effect and the increased post length insertion create a more favorable fracture to restore.
- Đăng nhập để gửi ý kiến